鋁板它在我們生活中的使用是很廣泛的，但是對于鋁板還有很多行外的人不是很了解，鋁板它進行加工的時候會經常出現浪費的現象，難免會出現浪費的情況，下面鋁板生產廠家就向大家介紹下：怎么減少鋁板不必要的浪費呢？
Aluminum plate is widely used in our life, but many people outside the industry do not know about aluminum plate very well. When aluminum plate is processed, waste often occurs, which is inevitable. The following aluminum plate manufacturer will introduce to you: How to reduce unnecessary waste of aluminum plate?
1.揉捏調直環節
1. Kneading and straightening link
調直這個環節，比較簡略讓型材產生曲折，操作員必定要注意調直所用的力度，假定力度過大就，或許型材就簡略產生變形、收口、桔皮等現象，而力氣過小就會產生型材調不直，構成型材曲折。
Straightening is a relatively simple link, which makes the profile zigzag. The operator must pay attention to the force used for straightening. If the force is too large, the profile may be slightly deformed, necked, orange peel and other phenomena, while if the force is too small, the profile will not be straightened, forming a profile zigzag.
2.揉捏裝框
2. Kneading and framing
這個環節也是非常重要的，鋸?fù)甓ǔ唛L度后，一般鋁板就要進行裝框了，這時應該要注意了：這料是大料仍是小料，是帶管料仍是平面模拉出來的料。
This link is also very important. After sawing the fixed length, the aluminum plate will be framed generally. At this time, it should be noted that this material is large or small, with tube or plane die.

一般來說，大料和帶管的料抬兩頭裝框不簡略構成曲折，但小料和平面模拉出來的料，抬兩頭就很簡略構成曲折，這時就應該從兩頭向中心挨近進行抬料裝框。但有的型材即便這樣還不可，這時咱們就需要把這類料放在已時效的型材上再抬到框里。
Generally speaking, it is not simple to frame large materials and materials with tubes by lifting both ends, but it is simple to frame small materials and materials pulled out by plane die by lifting both ends. At this time, it should be carried out from both ends to the center. But even if some profiles are not available, we need to put such materials on the aged profiles and then lift them into the frame.
3.表面處理上架
3. Surface treatment shelf
坯料經時效，硬度已達標，型材不會那么容易變彎曲，但是在上架時還是要注意，兩端抬料時，盡量避免上下大力波動，避免鋁板出現彎曲的情況。
After aging, the hardness of the blank has reached the standard, and the profile will not be so easy to bend. However, attention should be paid to when putting the blank on the shelf. When lifting the material at both ends, try to avoid strong fluctuation up and down to avoid bending of the aluminum plate.
上述就是關于怎么減少鋁板不必要的浪費呢？通過上述的介紹相信大家也詳細了解了，希望上述的分享可以幫到大家。更多相關信息就來我們網站http://www.0pb1.cn進行咨詢吧！
The above is about how to reduce the unnecessary waste of aluminum plate? Through the above introduction, I believe you have also understood in detail. I hope the above sharing can help you. Come to our website for more information http://www.0pb1.cn Consult!